Chevrolet Performance GM LS376/480 6.2L LS3 Base Crate Engine Long Block Assembly [495 HP 473 ft.-lbs of TQ]
Base Crate Engine
LS376/480 6.2L Performance Crate Engine
Starting with the potent LS3 foundation, GM added the proven GM Hot Cam camshaft to inject extra performance to create the LS376/480 crate engine.
LS376/480 TECH SPECS
- Engine Type: LS-Series Gen IV Small-Block V-8
- Displacement: 376 ci (6.2L)
- Bore x Stroke: 4.065 in. x 3.622 in. (103.25 x 92 mm)
- Block: Cast aluminum with six-bolt, cross-bolted main caps
- Crankshaft: Nodular iron
- Connecting Rods: Powdered metal
- Pistons: Hypereutectic aluminum
- Camshaft Type: Hydraulic roller
- Valve Lift: .525 in. intake / .525 in. exhaust
- Camshaft Duration (@.050 in.): 219-degrees intake / 228-degrees exhaust
- Cylinder Heads: Aluminum L92-style port; ''as cast'' with 68 cc chambers
- Valve Size: 2.165 in. intake / 1.590 in. exhaust
- Compression Ratio: 10.7:1
- Rocker Arms: Investment-cast, roller trunnion
- Rocker Arm Ratio: 1.7:1
- Recommended Fuel: Premium pump (92-octane)
- Maximum Recommended rpm: 6600
- Reluctor Wheel: 58X
- Balanced: Internal
Installation Notes:
- Will require intake manifold, throttle body, fuel rails, fuel injectors, exhaust manifolds, accessory drive, and an EFI controller
- LS3 is the same size and mounts the same as other LS-Series engines
- Includes a mid-wet sump oil pan installed. This oil pan will ONLY fit 2010-2015 Camaro SS/ZL1, 2012-2017 Caprice PPV, 2014-2017 Chevy SS, 2008-2009 Pontiac G8 chassis. THIS INSTALLED OIL PAN WILL NOT WORK WITH MUSCLE CAR LS ENGINE SWAPS. OIL PAN CHANGE IS REQUIRED FOR MUSCLE CAR LS ENGINE SWAPS.
Engine Break-In Procedure
Use only engine oil that meets dexos1 specifications. For track events or competitive driving, use Mobil 1 15W-50 engine oil. Fill the engine with oil and follow the proper engine priming procedure. Also check and fill as required any other necessary fluids such as coolant, power steering fluid, etc.
Start the engine and listen for any unusual noises. If no unusual noises are noted, run the engine at approximately 1000 RPM until normal operating temperature is reached. The engine should be driven at varying loads and conditions for the first 30 miles or one hour without wide open throttle (WOT) or sustained high RPM accelerations. Run five or six medium throttle (50%) accelerations to about 4000 RPM and back to idle (0% throttle) in gear. Run two or three hard throttle (WOT 100%) accelerations to about 4000 RPM and back to idle (0% throttle) in gear.
Change the engine oil and filter. Inspect the oil and the oil filter for any foreign particles to ensure that the engine is functioning properly. Drive the next 500 miles (12 to 15 engine hours) under normal conditions. Do not run the engine at its maximum rated engine speed. Also, do not expose the engine to extended periods of high load. Change the oil and filter again, inspect the oil and oil filter for any foreign particles to ensure that the engine is functioning properly.
19432424 supersedes 19420384
Specifications:
Part Type
Cylinder Head Material
Aluminum
Engine Block Material
Aluminum
Engine Make/Size
GM LS
Engine Assembly Style
Long block
Engine Balance
Internal
Assembled
Yes
Horsepower
495
Compression Ratio
10.7:1
Cylinder Heads Included
Yes
Camshaft Style
Hydraulic roller tappet
Intake Manifold Included
No
Carburetor Included
No
Throttle Body Included
No
Distributor Included
No
Oil Pan Included
Yes
Timing Cover Included
Yes
Water Pump Included
No
Harmonic Balancer Included
Yes
Valve Covers Included
Yes
Flexplate Included
No
Flywheel Included
No
Air Cleaner Included
No
Spark Plugs Included
No
Spark Plug Wires Included
No
Computer Included
No
Wiring Harness Included
No
Rear Main Seal Style
1-piece
Quantity
Sold individually
Engine Displacement
6.2L
Engine Type
Crate Engine
Shipping Weight:
465
Package Height:
36
Package Depth:
42
Package Width:
32
Manufacturer | Chevrolet Performance |
---|---|
Manufacturer Part No | 19432424 |
STAY CONNECTED
Sign up to be the first to hear about us